USER MANUAL
HWD-C1000TXVE-U
HWD-C1200TXVE-U
HWD–C1000TXVE ME-U
HWD–C1200TXVE ME-U
TABLE OF CONTENTS
BEFORE USE
>COMPONENTS
>PREPARATION
>SAFETY INSTRUCTIONS
>INSTALLATION
>CONTROL PANEL
USING THE APPLIANCE
>PROGRAM SELECTION
>CONSUMPTION AND TECHNICAL DATA
>WASHING METHODS
MAINTENANCE
>CLEANING & CARE
>DISPLAY CODES
>TROUBLESHOOTING
For Service Manual Please Download here
DISPLAY CODES AND SPECIAL FUNCTIONS
CODES = Err1
CAUSES = Door is not properly shut.
SOLUTIONS = Shut the door properly.
CODES = Err2
CAUSES = Drainage error, water not emptied within 4 minutes.
SOLUTIONS = Clean the fi lter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel
CODES = Err3
CAUSES = Temperature sensor not properly connected or damaged.
SOLUTIONS = Contact the maintenance personnel.
CODES = Err4
CAUSES = Heater error or laundry overload. The set temperature is not reached within specified
time. (Appears at the end of a cycle).
SOLUTIONS = Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel.
CODES = Err5
CAUSES = Water level not met in 8 minutes.
SOLUTIONS = Check the tap and the water pressure.
CODES = Err6
CAUSES = Dehumidification/heating error.
SOLUTIONS = Please contact the Service Center.
CODES = Err7
CAUSES = Motor overheat protection or damage.
SOLUTIONS = Please contact the Service Center.
CODES = Err8
CAUSES = Water overflow.
SOLUTIONS = Please contact the Service Center.
CODES = Err9
CAUSES = Error of the dryer temperature sensor.
SOLUTIONS = Please contact the Service Center.
CODES = Err10
CAUSES = Error of the water level sensor.
SOLUTIONS = Please contact the Service Center.
CODES = Err12
CAUSES = Error of the dryer water level sensor.
SOLUTIONS = Check whether clothes are dry or not and whether there is water still in the drum. If so allow excess humidity to escape from the appliance and try the drying cycle again.
CODES = Err13
CAUSES = Dryer heater error.
SOLUTIONS = Please contact the Service Center.
CODES = Unb
CAUSES = Laundry is unevenly distributed.
SOLUTIONS = Redistribute laundry to balance the drum.
CODES = EUAr
CAUSES = Communication error.
SOLUTIONS = Please contact the Service Center.
CODES = 1:16
CAUSES = Status information: remaining program time is 1 hour and 16 minutes.
CODES = 0:01
CAUSES = Status information: remaining program time is 1 minute.
CODES = 60°C
CAUSES = Status information: Wash temperature is 60°C.
CODES = --°C
CAUSES = No heat (cold wash).
CODES = 0
CAUSES = No spin.
CODES = 800
CAUSES = Status information: Spin speed 800 rpm.
CODES = L--1
CAUSES = Manually selected code when laundry weight is less than 1kg.
CODES = L--A
CAUSES = Manually selected code when drum is nearly full.
CODES = End
CAUSES = Program is finished
Control panel lock function: Press the "Delay" and the "Temperature" buttons simultaneously for 3 seconds after starting a program.
It can no longer be changed by operating buttons or knobs. To unlock press the "Delay" and "Start/Pause" buttons again for 3 seconds.
Power-off memory function: In case of abrupt power failure or the need to cut off the power during a program cycle, the present
settings will be saved and the preset operation will resume when the power is on again.
To cancel a program Press the "Start/Pause" button, then switch off the power and the program is automatically cancelled. Turn the program selector again to choose another program.
0 komentar:
Post a Comment