Thursday, September 1, 2011

LG Washing Machine WM2411HW Error Code

0 komentar
MODEL : WM2411HW/WM2011H*/WM1811CW
WM2432HW/WM2032H*/WM1832CW
WM0532HW/WD-10210BD/WD-12210(5)BD
WM2444H*M/WM2442H*/WM2042CW
WM0642H*

If you press the START/PAUSE button when an error is displayed, any error except "PE" will disappear and the machine will go into the pause status.
In case of " PE, tE, dE " if the error is not resolved within 20 sec., or the in case of other errors,
if the error is not resolved within 4 min., power will be turned off automatically and the error code will blink. But in the case of "FE", power will not be turned off.

ERROR = WATER INLET ERROR
SYMTOM = I E
CAUSE = • Correct water level (2 level) is not reached within 8 minutes after water is supplied or it does not reach the preset water level within 25 minutes.

ERROR = IMBALANCE ERROR
SYMTOM = U E
CAUSE = • The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.

ERROR = DRAIN ERROR
SYMTOM = 0 E
CAUSE = • Not fully drained within 10 minutes.

ERROR = OVER FLOW ERROR
SYMTOM = F E
CAUSE = • Water is overflowing (over 8 level).
¡ If "F E" is displayed, the drain pump will operate to the drain water automatically.

ERROR = PRESSURE SENSOR ERROR
SYMTOM = P E
CAUSE = • The SENSOR SWITCH ASSEMBLY is out of order.

ERROR = DOOR OPEN ERROR
SYMTOM = d E
CAUSE = • Door not all the way closed.
• Loose electrical connections at Door switch and
PWB Assembly.
• The DOOR SWITCH ASSEMBLY is out of order.

ERROR = HEATING ERROR
SYMTOM = t E
CAUSE = • The THERMISTOR is out order.

ERROR = OVER CURRENT ERROR
SYMTOM = C E
CAUSE = • MAIN PWB ASSEMBLY is out of order.
• Winding in the STATOR ASSEMBLY is short-circuited.

ERROR = LOCKED MOTOR ERROR
SYMTOM = L E
CAUSE = • The connector (3-pin, male, white) in the MOTOR HARNESS is not connected to the connector
(3-pin, female, white) of STATOR ASSEMBLY.
• The electric contact between the connectors (3-pin, male, white) in the MOTOR HARNESS
and 4-pin, female, white connector in the MAIN PWB ASSEMBLY is bad or unstable.
• The MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY is cut (open
circuited).
• The hall sensor is out of order/defective.

ERROR = BALL SENSOR ERROR
SYMTOM = b E
CAUSE = • Loose Ball Sensor Connector.
• Ball Sensor is out of order.
¡ Displayed only when the START / PAUSE button is first pressed in the QC Test Mode.

ERROR = EEPROM ERROR
SYMTOM = E E
CAUSE = • EEPROM is out of order.
¡ Displayed only when the START / PAUSE button is first pressed in the QC Test Mode.

ERROR = POWER FAILURE
SYMTOM = P F
CAUSE = • The washer experienced a power failure.

Read More ->>

Whirlpool Duet Front Loading Automatic Washer Fault Codes

2 komentar
Failure Code = FH
Fault Code Description = No water detected entering machine or pressure switch trip not detected
Solution = If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.
Or
If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.
Press PAUSE/CANCEL twice to clear the display.
Potential Causes
• If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way.
- Check for plugged or kinked inlet hoses or plugged screens in the inlet valves
- Verify inlet valve operation
• If there is water in the unit:
- Verify Drain pump operation
- Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch
• Verify there is not a siphon problem
• Verify wire harness connections to; Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU)
• Check all hoses for possible leaks
• Verify pressure switch operation
• Verify flow meter operation
• Verify CCU operation Replace failed component

Failure Code = F02
Fault Code Description = Long Drain
Solution = If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed. Press PAUSE/CANCEL twice to clear the display.
NOTE: After 4 minutes the “Sud” error will be displayed,
then 4 minutes later the F02 error code will be displayed.
Potential Causes
• Check the drain hose and make sure it is not plugged or kinked
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects
• If the above does not correct the problem replace the pump

Failure Code = F05
Fault Code Description = Water temperature sensor error
Solution = If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, the F05 error code will be displayed.
Potential Causes
• Check the Water Temperature Sensor, Heating Element and Element Relay
• Check connections to the Sensor, Heating Element and Relay Replace failed component

Failure Code = F06
Fault Code Description = Drive motor tachometer error
Solution = The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin the door will be unlocked after 3 minutes.
Potential Causes
• Check wire harness connections between the Drive Motor/Tachometer and the Motor ControlUnit (MCU), and between the MCU and the Central Control Unit (CCU)
• Check the Drive Motor
• Check the MCU
• Check the Wire Harness Replace failed component.

Failure Code = F07
Fault Code Description = Motor control unit error
Solution = The Central Control Unit has detected a short in the motor control unit. If a failure occurs during high-speed spin the door will be unlocked after 3 minutes.
Potential Causes
• Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
• Check the MCU
• Check the Drive Motor
• Check the Wire Harness Replace failed component.

Failure Code = F09
Fault Code Description = Overflow condition
Solution = If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.
Potential Causes
• Check the drain hose and make sure it is not plugged or kinked
• Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)
• Check / Clean Drain Pump Filter of foreign objects
• Check for Drain Pump Failure
• Check the Inlet Valve for proper shut off
• Check the Pressure switch for proper operation Replace failed component.

Failure Code = F10
Fault Code Description = Motor Control Unit (MCU) heat sink thermal trip
Solution = If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink which will stop motor functions and an F10 will be displayed.
Potential Causes
• Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation.
• Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU)
• Check the Drive system for any worn or failed components
• Check MCU
• Check Motor Replace failed component.

Failure Code = F11
Fault Code Description = Serial communication error
Solution = Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.
Potential Causes
• Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU)
• Check the Drive system for any worn or failed components
• Check MCU
• Check CCU
• Check Motor
• Check Wire Harness Replace failed component.


Failure Code = F13
Fault Code Description = Dispenser circuit error
Solution = If the dispenser motor is not able to be driven to it’s proper position.
Potential Causes
• Check mechanical linkage from dispenser motor to the top of the dispenser.
• Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU)
• Check Dispenser Motor Replace failed component.


Failure Code = F14
Fault Code Description = EEPROM error
Solution = The Central Control Unit (CCU) receives it’s data from an EEPROM onboard the CCU.
If there is an error reading this data it will cause this error.
Potential Causes
• A power glitch may cause this error. Try unplugging the Unit for two minutes to see if that fixes the error.
• Check CCU. Replace failed component.

Failure Code = F15
Fault Code Description = Motor Control Unit (MCU) error
Solution = If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode. Potential Causes
• Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU)
• Check Drive belt
• Check MCU
• Check Motor
• Check Wire Harness Replace failed component

Failure Code = Sud
Fault Code Description = SUDS LOCK (Overdose of detergent detected during the wash cycle)
Solution = The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. If “Sud” is displayed a potential suds lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds.
Potential Causes
• If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent. This should clear the unit of the excess detergent.
• Check the drain hose and make sure it is not plugged or kinked
• Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)
• Check / Clean Drain Pump Filter of foreign objects
• Check Drain Pump • Check the Pressure Switch
• Check CCU Replace failed component

Failure Code = FdL
Fault Code Description = Door lock error
Solution = A Door Lock Error occurs if the door cannot be locked. It will try to lock it 6 times before displaying the error.
Potential Causes
• Door Lock Mechanism broken or removed from the Door
• Check Door Lock/Switch Assembly
• Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU)
• Door Lock/Switch Assembly Failure Replace failed component

Failure Code = FdU
Fault Code Description = Door unlock error
Solution = A Door Unlock Error occurs if the door cannot be unlocked. It will try to unlock the door 6 times before displaying the error.
Potential Causes
• Door Lock Mechanism broken.
• Check Door Lock/Switch Assembly for foreign objects
• Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU)
• Door Lock/Switch Assembly Failure Replace failed component.
Note: The door lock/switch assembly can be manually unlocked.
To Manually unlock the door lock system:
1. Unplug the power cord from the outlet.
2. Remove the lower toe panel.
3. Reach up along the inside of the front panel and locate the bottom of the door latch assembly.
4. Located on the bottom of the door latch assembly is a tear-drop shaped tab.
5. Gently pull the tab down about 1/4 inch or until a click is heard. 6. The door may now be opened.

Read More ->>

Samsung Washing Machine WF-R1061 Error Code

0 komentar
1. An occurrence of an Error will make a sound of error melody for 5sec and continuously show one of the
Error Displays from the following errors. (But, Fault Check Led will fl ash for 0.5sec.)

2. All of the steering parts will be off at that time until that error was released.

3. Water Supply Error
- If there is no higher change in water frequency than 100Hz for 2 minutes during the initial time of water
supply and if water level doesn’t reach the preset level in 10 minutes, this error will occur.
This error will be released using Start/Pause button, which performs the initial condition of operation.
- Display : “4E”

4. Water Drain Error
- If water level frequency is still lower than the reset level frequency (25.20kHz) in 10 minutes after
starting of water drain, this error will occur.
This error will be released using Start/Pause button, which performs the initial condition of operation.
- Display : “5E”

5. Over Flow Error
- If an abnormal water level frequency is sensed (for occurrence of Over Flow :21.00kHz), Auto Power
Off may release this error and continuously progress water drain until the frequency reached 25.00kHz.
- If Over Flow is also sensed even after the following check of water level frequency indicating that error,
it functions to progress water drain.
- Display : “OE”

6. Door Open Error
- This error will be released by closing Door.
- Display : “dE”

7. Unbalance Error
- This error will be released by pressing start/pause S/W.
- DISPLAY : “ UE”

8. Water Heater Error
- This error will be released by turning off Power S/W.
- Display : “HE1”(Over Heat),
- Display : “HE2”, indicating no operation of HE.

9. Pressure S/W (Single Part Trouble) Error
Frequency signals(kHz) generated by water level S/W
Water Level = Abnormal Frequency
Low = 30.00 KHz
High = 15.00 KHz
- If the above frequency signals are displayed longer than 5sec, it indicates Pressure S/W Error.
- Drain water for 3 minutes for that Error, and turn OFF water drain pump. Pressure S/W Error display “ IE” will be shown. .

10. Abnormal Water Temperature ERROR
- Water drain begins if abnormal water temperature is sensed at the initial time of water supply. If the frequency higher than 25.20KHz is sensed, water will be drained by force.
- Display : “CE”
- This error will be released by turning off Power S/W.

11. Natural Drain/Water Leak Error
- If more than 4 times of water supply and safe water level of Heater are sensed for each course, this
error will occur.
- Display : “LE
- This error will be released by turning off Power S/W.

12. Tacho Error
- If Motor Tacho is abnormal, this error will occur.
- If Tacho signals are inputted less than 2 for 2sec after Motor started, this error will occur.
- Display : “3E”
- This error will be released by turning off Power S/W.

13. Motor TRIAC Short Error
- If Tacho signals are inputted more than 300 every 1sec in the operational interval less than 90RPM,
this error will occur.
Turn off Power S/W at that time.
- Display : “bE”
- This error will be released by turning off Power S/W.

14. Thermistor Abnormal Error
- If Thermistor circuit is abnormal, this error will occur.
- If Thermistor is lower than 0.2V or higher than 4.5V, this error will occur.
- Display :”tE”
- This error will be released by turning off Power S/W.
Read More ->>

Samsung Washing Machine WF9854RWE Error Code

0 komentar
CHECK THESE POINTS IF YOUR WASHING MACHINE

PROBLEM = Will not start
SOLUTION = • Make sure your washing machine is plugged in.
• Make sure the door is firmly closed.
• Make sure the water source tap(s) are turned on.
• Make sure to press the Start/Pause button.

PROBLEM = Has no water or not enough water
SOLUTION = • Turn the water tap on fully.
• Make sure the water source hose is not frozen.
• Straighten the water intake hoses.
• Clean the filter on the water intake hose.

PROBLEM = Has detergent remaining in the detergent drawer after the wash cycle is complete
SOLUTION = • Make sure your washing machine is running with sufficient water pressure.
• Make sure the detergent is added to the center of the detergent drawer.

PROBLEM = Vibrates or is too noisy
SOLUTION = • Make sure your washing machine is on a level surface. If the surface is not level, adjust the washing machine feet to level the appliance.
• Make sure that the shipping bolts are removed.
• Make sure your washing machine is not touching any other object.
• Make sure the laundry load is balanced.

PROBLEM = The washing machine does not drain and/or spin
SOLUTION = • Straighten the drain hose. Eliminate kinked hoses.
• Make sure the debris filter is not clogged.

PROBLEM = Door is locked shut or will not open.
SOLUTION = • The door will not open until 3 minutes after the machine stops or the power turns off.

If the problem persists, contact your local Samsung Customer Service.

INFORMATION CODES
If your washing machine malfunctions, you may see an information code on the display. If this happens,
please check the table below and try the suggested solution before calling Customer Service

CODE SYMBOL = dE
SOLUTION = Close the door.

CODE SYMBOL = 4E
SOLUTION = • Make sure the source water tap is turned on.
• Check the water pressure

CODE SYMBOL = 5E
SOLUTION = • Clean the debris filter.
• Make sure the drainage hose is installed correctly.

CODE SYMBOL =UE
SOLUTION = • The laundry load is unbalanced. Redistribute the load. If only one item
of clothing needs washing, such as a bathrobe or pair of jeans, the
final spin result might be unsatisfactory and an “UE” error message
will be shown in the display window.

CODE SYMBOL = cE/3E
SOLUTION = • Call the after-sales service.

For any codes not listed above, or if the suggested solution doesn’t fix the problem, call your Samsung
Service Centre or local Samsung dealer.

CODE SYMBOL = SUdS
SOLUTION = • Indicates excessive sudsing.
• Wait until the suds removes.
Read More ->>

Samsung Washing Machine WF218ANB WF218ANW Error Code

0 komentar
INFORMATION CODES
Information codes may be displayed to help you better understand what is occurring with your Washer.

CODE SYMBOL = dc
MEANING = Unbalanced load prevented your Washer from spinning.
SOLUTION = Redistribute the load, press the Start/Pause Button.

CODE SYMBOL = dL
MEANING = Door is unlocked when Washer is running.
SOLUTION = Press the Power button to turn off your Washer, then restart the cycle. If the code reappears, call for service.

CODE SYMBOL = d5
MEANING = Door is open when Washer is running.
SOLUTION = Close the door tightly and restart the cycle. If the code reappears, call for service.

CODE SYMBOL = FL
MEANING = Your Washer failed to lock the door.
SOLUTION = Close the door tightly and restart the cycle. If the code reappears, call for service.

CODE SYMBOL = Hr
MEANING = Water temperature control problem. (Heater Control problem)
SOLUTION = Call for service.

CODE SYMBOL = LE
MEANING = Your Washer has tried to fill but has not reached the proper water level.
SOLUTION = Call for service.

CODE SYMBOL = L0
MEANING = The door will not unlock.
SOLUTION = Make sure the door is firmly closed.
Push the Power button to turn off your Washer, then turn it on again. If the code reappears, call for service.

CODE SYMBOL = E3
MEANING = Motor not running properly.
SOLUTION = Restart the cycle pressing the Start/Pause Button. If the code reappears, call for service.

CODE SYMBOL = nd
MEANING = Your washer is not draining.
It can also mean that the unit senses a small clog while draining
SOLUTION = Before calling for service, check the following.
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water.
If it still does not drain, call for service.

CODE SYMBOL = nF
MEANING = Your Washer has tried to fill but was unsuccessful.
SOLUTION = Make sure the water faucets are open all the way. Check for kinked hoses.
Check the inlet screens on the fill hoses.

CODE SYMBOL = 5r
MEANING = Problem with control.
SOLUTION = Call for service.

CODE SYMBOL = PF
MEANING = Electric service was lost when Washer was running.
SOLUTION = Restart the cycle by pressing the Start/Pause Button.

CODE SYMBOL = 0E
MEANING = A fault is detected in the water level sensor.
SOLUTION = Call for service

CODE SYMBOL = E2
MEANING = Jammed Key.
SOLUTION = Call for service

CODE SYMBOL = bE
MEANING = Motor speed sensor problem.
SOLUTION = Restart the cycle.
If the code reappears, call for service.
Read More ->>
 

| Code Error Washing Machine © 2014. All Rights Reserved | Template Style by My Blogger Tricks .com | Design by Brian Gardner | Back To Top |